Get Ready for the Solar Eclipse! Home made Solar Finderscope

It was whilst I was making the solar filter for my telescope (find that article here) that I seriously started to think about how I was to find the object of study in the eyepiece. I knew that one recommended method was to move the scope such that the shadow cast by it onto the ground was  minimal i.e. a round telescope tube's silhouette would be circular when directly aligned with the sun. If the 'scope was not aligned then the shadow cast would become elongated.

How to make a solar finderscope from scrap



I realised that for next to zero cost, I could fabricate a finder that could fit in the existing finderscope mount thus solving  a secondary problem, that of the original finderscope if left without lens caps could train a focused image of the sun onto the top of my head!

Materials

32mm (1¼") diameter offcut of PVC water pipe
1 piece 50mm (2") wide masking tape
1 square of silvered wine bag liner or similar opaque flexible material such as cooking foil...
1 elastic band

Solar finderscope - DIY from scrap materials


Construction

I based the finderscope on the principle of the camera obscura, that is a pinhole pierced in an opaque film at the front of a tube would allow the sun's image to be projected onto a translucent screen at the other end (also a little like a pinhole camera with the film being replaced by the translucent screen).

Making a solar finderscope using scrap materials


I had a short length of 32mm (1¼") diameter PVC pipe and I covered one end with a piece of opaque, silvered plastic from a 'bag in box' wine dispenser. I used an elastic band to attach the square of film. The 'screen' at the other end of the tube was simply a piece of 50mm (2") wide masking tape stretched over the end and adhered around the wall of the tube. I pierced a tiny hole in the approximate centre of the silvered plastic film.

Fitting a homemade solar finderscope
I removed the original finderscope from the telescope and slid the plastic tube in place. The finderscope on my Celestron C8 is a 6 x 30 and this meant that the 32mm outside diameter PVC tube fitted perfectly and still allowed for adjustment using the three screws on the finderscope mount.

First Light

sunspot image achieved with homemade solar filter and finderscope
Once the finderscope was in place and the filter attached to the telescope, I was then able to align it.

Firstly I had to find the sun in the main telescope (with the solar filter in place) for this I used the technique described in the introduction. Once I was able to get the image of the sun central in the eyepiece of the telescope, it was then possible to adjust the finderscope so that the bright image of the sun was visible on the masking tape 'screen' (see image above).

Fine adjustments were made to centralise the image.

And now if you'd like to, sit back and watch the film:



plus realtime making of the finder in under 1 minute....


Modifications

Telescope for solar observation
The offcut tube I used was 350mm (14") long. This was a quick job as I needed the scope for immediate use. A shorter length tube could be used and it would give a much wider field of view in which to find the sun.  Similarly, with a larger diameter PVC tube. However, I used the scrap I had to hand and this fitted the existing finderscope mount.

Please feel free to share this article, comment and/or ask for further information.

Until next time!

Cheers, Andy
© Andy Colley 2017



RELATED ARTICLES

Home-Made Locking Solar Filter

How to make a robust, lockable solar filter for your telescope from repurposed materials and purchased AstroSolar film. This will allow you to enter the amazing world of solar astronomy...read more

Binocular Collimation Quick and Easy Method without Prism Adjustment

I was initially put off from correcting an optical fault in an old pair of Porro prism binoculars because all I had seen or read online involved prism adjustment...read more


RETURN TO GREEN LEVER CONTENTS PAGE FOR MORE ARTICLES 

No comments:

Post a Comment